Autonetics Training Programme

Full Automation

1) Post Graduate Diploma in Industrial Automation

  • Basics of automation & PLC
  • Programmable logic controller
  • Supervisory control & data acquisition(SCADA)
  • Human Machine Interface(HMI)
  • Instrumentation system
  • Electrical system
  • Drives
  • Mechatronics system
  • Embedded system
  • Soft skill and interview guidelines

2) PLC (Programmable Logic controller) [7 WEEK]

  • Introduction to PLC hardware (AB ,Siemens,Gc-Fanuc ,ABB,Mitsubishi)
  • Architecture of PLC
  • PLC fundamentals
  • Information about PLC components
  • Types of input output
  • Source sink concepts in PLC
  • Flag concepts
  • Wiring Installation concept
  • Introduction to PLC Programming software
  • Addressing concepts
  • Introduction to Byte, bit & word concept
  • Detail Programming
  • Timer, counter ,block programming
  • Advanced Instruction
  • File handling
  • Upload download & Monitoring
  • Forcing Input output
  • Troubleshooting and fault diagnosis of plc
  • Programming assignments for real time application

3) SCADA (Supervisory Control and data Acquisition) [1 WEEK]

  • Introduction of SCADA software (Wincc, Rockwell Solution)
  • Applications of SCADA software
  • Creating database of Tags
  • Creating and Editing graphics display with animation
  • Data entry / Start stop command / analog input
  • Sizing / movement / blinking/ visibility /filling
  • Trending
  • Script logic writing
  • Recipe management
  • Security management
  • Types of Window
  • Database connectivity
  • Communication with PLC
  • Troubleshooting

4) HMI (Human Machine Interface) [1 WEEK]

  • Introduction to HMI (siemence)
  • Interfacing and networking with PLC
  • Creating screen
  • Creating Database
  • Navigation between screen
  • User input/ output display
  • Function key
  • Uploading/ Downloading application
  • Dynamic Representation
  • Alarm
  • Security
  • Trends, recipe management

5) Instrumentation system [1 WEEK]

  • Measurement Definition
  • Classification of Instrumentation
  • Pressure measurement
  • Flow measurement
  • Temperature measurement
  • Level measurement
  • All transmitters (2,3,4 wire)
  • Types of control system
  • PID controller

6) Electrical system [1 WEEK]

    Electrical Fundamental:-
  • Electrical system Measurements.
  • Electrical parameter Calculations.
  • Principle of AC generation.
  • Front control and switching concept.

  • Switchgear/Protection device:-
  • Electrical fault detection.
  • Fuses
  • MCB / MCCB / ACB
  • Contactor / OLR / MPCB / ELCB

  • MOTOR and Starter:-
  • AC motor types.
  • DC motor types.
  • Calculation of motor.
  • Starter Principle
  • Direct ON line(DOL).
  • Star Delta circuit.
  • Single phase Motor
  • Split phase.
  • Capacitor start.
  • Shaded pole.
  • Universal motor.

  • Transformer:-
  • Basic types of transformer.
  • Generator and characteristic.

7) Mechatronics system [1 WEEK]

  • Introduction to Hydraulic and Pneumatic
  • Basics principle of operation
  • Various types of Hydraulic and Pneumatic
  • Block diagram
  • Single and double acting cylinder
  • Construction operation and application, maintenance
  • Troubleshooting and Fault finding of hydraulic system
  • Actuator
  • Air compressor
  • How to check air compressor
  • Disadvantage of Hydraulic and Pneumatic
  • Symbols used in Pneumatic
  • Direction control value

8) Embedded [1 WEEK]

  • Microcontrollers.
  • System Development concepts.
  • Understanding target board .
  • Understanding microcontroller.
  • Work environment and development guidelines.
  • Interfaces - sensors and modules.
  • Interrupts and timers.
  • Data storage.
  • C programming.
  • Robotics

9) Drives [1 WEEK]

  • Dc Motor
  • Ac Motor
  • Motor Review
  • Loads
  • Servo Motor
  • Stepper Motor
  • Requirements of Drive
  • Dc Drives
  • Ac Drives
  • Bypassing
  • User/operator interface

Get in Touch